What's New In The 3D Printer World

Prevention is the key

Over the last few weeks there have been posts on social media relating to fires being caused by 3D printers.

Continue reading
  17984 Hits
  3 Comments
Recent Comments
Kevin West
As mention this is controversial, and think this is a preferential choice. I have never had any issues with tinning wires includin... Read More
Sunday, 05 August 2018 01:23
17984 Hits
3 Comments

X - Y Axis

X - Y Axis

One of the biggest flaws in my opinion of the X5S are the belt pulley mounts, as the load placed on them when the belts are in tension is located in one point on each fixing.

Continue reading
  15532 Hits
  0 Comments
15532 Hits
0 Comments

Z - Axis Linear Rail Installation

Z - Axis Linear Rail Installation

Preparations the key for the rails to run correctly, and lubricating the rails is best done prior to installation.

Continue reading
  15258 Hits
  0 Comments
15258 Hits
0 Comments

Z Axis Mount

Z-Axis Mount

I reccomend you replace the Z-Axis mount even if you do not intend to use a linear rail.

Continue reading
  15535 Hits
  0 Comments
15535 Hits
0 Comments

Customized Tronxy X5S Frame

The frame of the printer is the most important part, and if you get this part of build wrong everything else will go out of whack very quickly. I do not recommend printing certain part for strength and stability reasons.

Continue reading
  15237 Hits
  0 Comments
15237 Hits
0 Comments

Customized Tronxy X5S

I keep on getting asked to keep members of Groups on Facebook to keep the upto date with the Customisation of My second X5S. So I have created a special section on our forum to create a build log,

Continue reading
  19635 Hits
  3 Comments
Recent Comments
Gernot Lepuschitz
Hi - you wrote: "So I have created a special section on our forum to create a build log..." - but I cannot find this section in th... Read More
Thursday, 24 October 2019 09:03
Dale Johnston
Scott; Finally got around to installing the motherboard for the x5s that i got off you. Works but it has a problem. Thought it was... Read More
Monday, 10 February 2020 22:53
Scott Worthington
You do not connect to the firmware at all you can do a gcode file with the needed changes and save code run as print then reboot p... Read More
Monday, 10 February 2020 23:05
19635 Hits
3 Comments

Tap Drill Chart

There are six categories of standard taps. We have broken down the drill size recommendations into those six categories which appear below

 

Metric Size

Letter Size

Metric taps

milimeter Thread

Continue reading
  16986 Hits
  0 Comments
16986 Hits
0 Comments

The Shop Is Back

After working on the shop site over the weekend.The team are happy to announce the site is back up and running...

  21479 Hits
  0 Comments
21479 Hits
0 Comments

G Codes and M Codes for 3D printing

          You can customize the beginning and ending code that your slicer adds to the gcode files it produces to automate certain tasks or produce a more desired behavior. Below are suggestions for these codes.

For a list of gcode commands and their usage continue to the bottom of the post.

Continue reading
  50039 Hits
  2 Comments
Recent Comments
Dan Gould
How about printers that have dual extruder heads? Are there codes for those? Thanks Dan
Friday, 09 February 2018 13:49
Dan Gould
I think it would need to recognise T# as a Tool selection. More investigation needed by me I think. I'd like to modify my Tronxy X... Read More
Friday, 09 February 2018 13:53
50039 Hits
2 Comments

How to calculate power requirements of 3D Printer & safeguard Controller

          Most new users to 3D Printing buy a kit due to the low cost in owning one, however
most do not have any engineering background. This in it's self is not an issue as we
want to encourage new users to this fascinating hobby,
but can cause problems when users decide to modify or upgrade, repair their printer.
The power supply that come's with you printer has some marking on it regarding to the power "WATTS", however most will not show the most important factor the
number of "AMPS" the Power Supply will actually deliver......

Continue reading
  28537 Hits
  1 Comment
28537 Hits
1 Comment

We Have Gone Live

We Have Gone Live.

Welcome you all new members who have joined us.

While the site is new there might be a few buggy issues, and to help us give you a great user experience let us know if you find something wrong.

Also if you think of somthing to add to any of the main areas of the site do tell us.

Many Thanks For Joining.

The Team.

Continue reading
  15112 Hits
  0 Comments
15112 Hits
0 Comments

We are close to completion

It's getting there

Hopefully by the end of the weekend the website will be ready for everyone to enjoy.

  12418 Hits
  0 Comments
12418 Hits
0 Comments

To keep the site live and make improvements Please consider Donating. Thank you for your donation.